中国中车福田玉柴136马力4200轴距洒水车车型

洒水车水泵的拆卸方法：
First of all, this paper introduces the method of removing the water pump:
这种方法所有的洒水车都通用的，多的一点点的不同之处，也是非常的好看明白的！
This way all of the sprinkler are common, the most a little bit different, but also very good looking!
1.找到放油螺丝将其旋下，打开放水阀门将水泵里的剩余液体和齿轮箱里的润滑油排出干净。免得洒水车水泵里的水倒出弄脏衣服。
1 find the oil drain screw to screw down, open the drain valve will be the residual liquid in the pump and the gear box of the lubricating oil discharged clean. Lest the sprinkler pump the water out of dirty clothes.
2.把管道和机座螺栓一一拆除，将泵取下，拆去进口法兰。拆下法兰盘的时候要记住水泵进出口的安装位置，方便安装时对接进出口。
2 of the pipeline and the base bolt one one is removed, the pump will remove, remove the inlet flange. Remove flange plate when you want to remember the installation location of the pump inlet and outlet, to facilitate the installation of the docking port.
3.拆叶轮。先旋下叶轮螺母，再拆下洒水车水泵与齿轮箱的联接螺母，然后用M12螺栓慢慢的顶开螺孔中旋入的M12螺栓，，这时候泵体和齿轮箱同时被顶开，级叶轮自动脱出，，第二级叶轮，机械密封就和齿轮箱一起与泵体分离。
3 open impeller. First unscrew the impeller nut, to remove the shed sprinkler water pump and the gear box connecting nut, and M12 bolt slowly to the top of open screw screw M12 bolt, this time the pump body and the gear box also is to open the top, first stage impeller automatic prolapse, the second stage impeller, mechanical seal and gear box together with the pump body separation.
4.拆去齿轮箱盖和输入轴承盖，将输入轴承由水泵体侧打出，后从箱体上方将主动齿轮取出。
4 remove the gear box cover and enter the bearing cover, the input bearing by the pump body side, and finally from the top of the box will take the initiative to remove the gear.
洒水泵安装方法和拆卸的步骤是相对的，只是要注意一下几点：
Sprinkler installation and removal of the steps are relative, but to pay attention to the following points:
1.安装前应先把洒水泵两侧的撑脚卸下，将泵轴心与联轴器对准，把齿轮箱上的四个螺栓拧紧后再将撑脚装上。
1 before the installation of the pump should be on both sides of the foot of the foot of the pump, the pump shaft and shaft coupling alignment, the gear box on the four bolts after tightening will be installed on the support.
2.注意对整齐油封间隙，调试叶轮的位置，不要使其在旋转时擦到箱体。
2 pay attention to the neat oil seal clearance, the position of the impeller, do not make it in the rotation to wipe the box.
3.洒水车水泵进出口管路紧固在车身上，不能使其重量被泵承受，管路中还应加装过滤网。
3 sprinkler pump inlet and outlet pipe must be fixed on the body, can not be the weight of the pump to bear, the pipeline should also be installed filter.

喷洒车，又称为多功能绿化洒水车。用于城市道路、大型厂区、、园林等单位清洁路面、卫生、防尘、浇水、喷洒农药等，以达到美化环境的作用。

同时可以用于临时应急消防洒水,每辆洒水车都配备消防接口。
东风洒水车
东风洒水车
由发动机带动变速箱，变速箱上安装的取力器带动洒水泵，洒水泵产生主要动力，将罐体内部的液体通过管网喷洒出去。自吸高度:≤7m，洒水宽度:≥20m，大射程:≥28m;可调节成柱状，射程≥28m;也可调节成雾状，射程≥5m。

前喷后洒，前装有鸭形喷嘴或圆头冲嘴，后面装有圆柱开洒水喷嘴或莲蓬头喷嘴，后部有一工作平台，装配有高压水炮。后部还可装8个喷嘴(选装)喷水器一般用于冲洗街道。

洒水车又称为喷洒车、多功能洒水车、园林绿化洒水车、水罐车、运水车。
洒水车适合于各种路面冲洗，树木、绿化带、草坪绿化，道路、厂矿企业施工建设，高空建筑冲洗。具有洒水、压尘、高、低位喷洒，农喷洒、护栏冲洗等功能，还具有运水、排水，应急消防等功能。