厂家东道防爆LED防爆灯LED防爆加油站灯防爆油井灯防爆灯壳体

厂家东道防爆LED防爆灯LED防爆加油站灯防爆油井灯防爆灯壳体
厂家东道防爆LED防爆灯LED防爆加油站灯防爆油井灯防爆灯壳体
厂家东道防爆LED防爆灯LED防爆加油站灯防爆油井灯防爆灯壳体
品牌：东道防爆 型号：DOD 输入电压：100-240（V）
LED灯珠颗数：99（颗） 封装工艺：单颗式 LED芯片品牌：普瑞
光通量：10000（lm） 色温：6000-6500（K） 灯具光效：120（lm/W）
功率因数：≥0.95 发光角度：120（度） 显色指数：75
防护等级：IP65 认证：防爆认证，专利认证， 使用场合：油、化工、工厂、煤矿、隧道等易燃医爆气体环境中的安全照明。
尺寸：335*275*150（mm） 寿命：100000（H） 外壳材质：铝合金
重量：9000（g） 功率：1250 灯光颜色：正白
光源类型：LED
适用范围 Application
SDB48-L适用于ⅡA、ⅡB类含有爆炸性气体或蒸汽环境，温度组别为T1-T6的1区、2区室内外危险场气或20区、21区、22区爆炸性或可
燃性粉尘场所室内外照明。
It is applicable for explosive gas or steam atmospheres of CAT ⅡA, ⅡB , temperature classification from T1 to T6, is mainly applied to Zone
1 and Zone 2 hazardous locations indoors and outdoors, or explosive or combustible dust atmospheres Zones 20, 21 and 22, used for lighting indoors and
outdoors.正常工作条件 Normal working conditions
◆安装地点的海拔不超过2000m；
◆周围环境温为-40℃～+40℃，且24h内的平均温度值不超过+35℃;
◆周围空气相对湿度不大于95%(+25℃)
◆在无剧烈振动、冲击及摇动的地方；
◆适用于1区、2区、ⅡA、ⅡB、ⅡC类及T1～T6组爆炸性气体环境场所；
◆Altitude of the installation site shall not beyond 2000m;
◆Ambient temperature should be within -40℃～+40℃, average temperature within 24h shall not exceed +35℃;
◆Ambient air relative humidity shall not exceed 95% (+25℃);
◆Installation site shall be free of severe vibration, shock or shake;
◆It is applicable for explosive gas atmospheres Zones 1 and 2, CAT ⅡA, ⅡB and ⅡC, and temperature classification from T1 to T6.
产品结构性能 Product structure performance
1、灯具防爆型式为隔爆型或粉尘防爆型，适用于气体或粉尘爆炸危险场所照明使用，
2、灯具由光源腔，电器腔构成密闭式设计。
3、灯具由铝合金压铸成型，电器腔内含LED电源，接线端子等电器，光源腔内部设有镜面反射器。
玻璃采用钢化玻璃，透光率高，抗冲击强。网罩采用不锈钢，表面聚酯粉末喷涂(防腐型外壳经过特殊金属外处理再表面聚酯粉末喷涂)。
4、灯具外露紧固件采用铝材，安装有橡胶密封垫，密封可靠，防水防尘防腐性强。内置橡胶件，电线外皮，塑料全采用抗高温抗 阻燃件，更安全可靠。
5、本灯具适用于管吊式，吸顶式、吸壁式、立杆式、支架式多种安装方式。
6、电源采用整体散热技术，短路、过流、过压、过温保护。
7、灯具具有命、高亮度抗震性好、外观美观大方，长期使用免维护。是节能、环保理想的防爆灯具。1、灯具防爆型式为隔爆型或粉尘防爆型，适用于气体或粉尘爆炸危险场所照明使用，
2、灯具由光源腔，电器腔构成密闭式设计。
3、灯具由铝合金压铸成型，电器腔内含LED电源，接线端子等电器，光源腔内部设有镜面反射器。
玻璃采用钢化玻璃，透光率高，抗冲击强。网罩采用不锈钢，表面聚酯粉末喷涂(防腐型外壳经过特殊金属外处理再表面聚酯粉末喷涂)。
4、灯具外露紧固件采用铝材，安装有橡胶密封垫，密封可靠，防水防尘防腐性强。内置橡胶件，电线外皮，塑料全采用抗高温抗
阻燃件，更安全可靠。
5、本灯具适用于管吊式，吸顶式、吸壁式、立杆式、支架式多种安装方式。
6、电源采用整体散热技术，短路、过流、过压、过温保护。
7、灯具具有命、高亮度抗震性好、外观美观大方，长期使用免维护。是节能、环保理想的防爆灯具。
1. The lamp is of flameproof or dust explosion-proof type, is suitable for gas or dust explosion hazardous locations.
2. By the light source of lamps and lanterns cavity, electrical constitute a closed cavity design.
3. Lamps by aluminum alloy die-casting molding, electrical cavity embedded LED power supply, terminals such as electronics, light source cavity with
internal mirror reflector.USES toughened glass, high transmittance, strong impact resistance. Net is made of high quality stainless steel, the surface
of polyester powder coating (anti-corrosion type shell with special metal processing and surface polyester powder coating).
4. The exposed fasteners are made of high quality stainless steel, are equipped with rubber gasket, with reliable sealing performance, excellent waterproof,
dustproof and anti-corrosive properties. Built-in rubber parts, wire jacket, and plastics all use high-temperature resistant and flame retardant articles,
safer and more reliable.
5. All kinds of installation ways are suitable, such as hanging type, ceiling type, wall-mounted type, post type, bracket type, etc.
6. The power supply adopts integral heat dissipation technology, with protections against short circuit, over current, over voltage, over heat, etc.
7. The lamp enjoys long service life, high brightness, good antiknock characteristic, elegant appearance, maintenance free. It is an ideal product for energy
saving and environment protection. 使用与维护 The use and maintenance
◆防爆灯在使用前，要仔细检查铭牌内容与客户订货是否相符合；
◆防爆灯在安装时先将进线电缆通过引入装置接到接线腔的接线端子上，并压紧密封圈，使电缆密封好，接好接地线，紧固好螺钉，上述
各项检查无误后，即可通电使用；
◆防爆灯不得随意拆卸，维护时，须断开前级电源后才可开盖检修；一般不需要检修本产品具有命特点。
◆在维修过程中不得损坏隔爆面，维修后涂204-1防锈油，合好盖，紧固后方可使用；
◆防爆灯应定期检查，清理透明件表面灰尘。
◆障碍物距防爆外壳大于30mm。
◆Before putting into operation, please check the nameplate first to make sure that the parameters are what you ordered.
◆Before installing the lamp, please connect the incoming cable to the terminal block in the wiring chamber through the entry device, compress the seal
ring, well connect earth wire, and tighten the screws. Examine and make sure everything is right, then switch on the power supply;
◆Don't disassemble the lamp randomly, when repairing, must cut off the power supply first before opening the cover for maintenance; usually it need
not to repair, as it is featured with long service life.
◆Pay attention to not hurt the explosion-suppression surface during maintenance, coat with anti-rust oil 204-1 after maintenance, close the clover,
make sure to tighten it before using;
◆Inspect the lamp regularly, clear away the dust from the transparent parts.
◆Distance from the explosion-proof shell to the obstacle should be more than 30mm.

售后服务期：

　　公司先后通过了船级社ISO9001质量管理体系认证，国家灯具质量监督中心等机构认证。产品保用5年产品，整灯保用2年。自购买之日起2年内，产品正常使用下出现任何故障，由本公司负责免费维修，2年后仅收取材料费。
江苏常州