36齿手持式电动凿毛机，新型便携性刀头可更换

36齿手持式电动凿毛机，新型便携性刀头可更换

用途：

电动凿毛机是针对个别用户需求研发的一种新型便携性电动凿毛机.工作效率每小时可

拉毛15平方左右.工作宽度为12公分.本机采用无极变速机.使用寿命长.刀头和刀轴全部

为钨钢合金材质.广泛用于墙面翻新打毛，板材荔枝面打磨.高速公路.桥梁.市政工程及

市政装修等等建筑工程.从而达到粗糙度用于二次铺装。

Application of electric hand-held Chisel: Electric Chisel is a new type of 

portable electric Chisel. Work efficiency per hour can stretch about 15 

square. The working width is 12 cm. This machine adopts stepless speed 

change machine. Long Service Life. The cutter head and shaft are all made of 

tungsten steel. Widely used in wall surface retreading hair, board Litchi 

surface grinding. Highway. The bridge. Municipal Engineering and municipal 

decoration and other construction projects. So as to achieve roughness for 

the secondary paving.

本产品是新品，适合小面积的地面拉毛和凿毛，机身小，重量轻，拿在手里就可以轻松

的完成工作。

This product is a new product, suitable for small area of the ground and 

chipping, small body, light weight, in the hands can easily complete the 

work. 

手持电动凿毛机相比较气动凿毛机省去了气泵的麻烦，改变了传统的凿毛法，大大加快

了工作效率。

Hand-held electric roughing machine compared with pneumatic roughing machine 

saves the trouble of Air Pump, changes the traditional roughing method, 

greatly speeds up the work efficiency.

手持电动凿毛机广泛适用于混凝土凿毛，花岗岩、大理石等石材的荔枝板面凿毛，刀头

可更换，改进了以往的施工工艺，使凿毛后的外观更均匀，也降低了制作成本。

手持电动凿毛机细节

环形把手，操作更舒适

三头凿毛盘，自由拆卸更换

旋转式安装接口，加入垫圈更紧密

设置调速开关，开机先低速后高速

Hand-held electric roughing machine is widely used in concrete roughing, 

granite, marble and other Stone Litchi Plate surface roughing, cutting head 

can be replaced, improved the previous construction technology, so that the 

appearance of roughing more uniform, but also reduce the production cost. 

Hand-held Electric Chisel details ring handle, operation more comfortable 

three-head Chisel Wool Plate, free removal and replacement of rotating 

installation interface, add washer more tightly set speed switch, start 

after low speed high speed

24齿合金凿毛滚轮

手持电动凿毛机参数 

功率 1200W

电压220V                

磨盘尺寸 120mm

磨轮 3个

磨轮材质 合金钢

工作效率 15-18㎡/h

重量 5KG

手持电动凿毛机特点

多齿凿毛头，受力均匀

质量可靠，配件精工细作

新盘与机器配比更加合理，更便于施工操作

重量减轻30%，操作灵活度提升，施工疲劳度减轻

新盘与机器配合升级，增强机器齿轮寿命，磨损度降低

注意事项

机器先与地面接触放平，由低速启动

转速不得超过1300R/MIN，转速过高容易损坏机器，效果不好

Electric Chisel features multi-tooth Chisel head, uniform force, high 

efficiency, high quality and reliability, precision new plate and machine 

accessories with a more reasonable ratio, more convenient construction 

operation weight reduced by 30% , operating flexibility increased, the 

construction fatigue degree reduces the new plate and the machine matches 

the upgrade, strengthens the machine Gear Life, the attrition degree reduces 

the matters needing attention the machine first contacts the level with the 

ground, starts the rotational speed not to exceed 1300 R/min by the low 

speed, the rotational speed is too high easy to damage the machine, the 

effect is not good