胶体蓄电池生产厂家

胶体系列
Nominal Voltage: 12V 2V
Design Life: 10-12 years
Capacity: from 31AH to 3000AH
Applications: Emergency lighting system Electric tool Geodesic apparatus. Fire alarm Safety Alarm, UPS system. Control system，Medical treatment equipment. Back-up power system. Portable power. Power system, Railway system. Ship quipment, Military，equipment, Telephone switching system than 350 cycles on 80 deep discharge, long life and low self-discharge, high recovery capability on deep discharge.
Characteristic: Special lead-calcium alloy plate and high purity additive ensure more than 350 cycles on 80 deep discharge long life and low self-discharge. high recovery capability on deep discharge.
电压：12V2V
设计寿命：10－12年
容量：31AH－3000AH
应用范图：应急原明；电动工具；电动玩具；测量位器；消防报管；安全昏报；UPS系统；控割系；区行被：备用电力能源；计算机备用电源；电力系统；铁路系统；发电站；船船设备；设备及电话交换机等
性能特点：采用特殊的正极板福铅合金以及特的铅音配方和添加剂，使电池80％限度放电循环寿会达到350次以上。寿命长，衰减慢，放电恢复性能良好。
性能特点
Characteeristics
1、阀控式铅酸蓄电池免维护，循环寿命长。
Valve Regulated Lead Acid (VRLA) Battery, Maintenance Free (no topping up)
2、采用率的超细玻璃纤维（AGM)隔板，气体符合效率达到98％
Absorbent Glass Mat(AGM)Separators technology for high efficiency, gas absorption of up to 98%
3、特殊的高锡合金板栅材料，降低了板栅的腐蚀效率，延长电池使用寿命了电池的寿命。
Advanced lead tin calcium alloy, reduces grid corrosion & promotes long battery life
4、失水极少无电解液层化现象。
Little water losing, no electrolyte stratification phenomenon
5、充放电能力强。
Performance excels at high rates of discharge & recharge
6、开闭阀灵敏，阻止外部空气侵入，释放多余气体保障安全，保持一定的范围的气压促进气体复合。
Vent Valve -allows the release of excess gases & prevents case rupture
7、良好的深放电恢复性能。
Good deep discharge resilience performance
8、安全性能好，正常使用下电解液不漏出，无电池膨胀破裂。
Excellent safety performance: No electrolyte leakage, battery swelling and cracking under correct operation
9、热容量大，减少了热失控的风险，不易干涸，可在较恶劣的环境中使用。
High thermal capacity, reduce the risk of thermal out of control and drying hard, can be used in bad environment
10、耐大电流性能好：完全充电状态的电池2CA放电分钟或10CA放电5分钟。无导电部分熔断，无外观变形
Good resistance to high current: The fully charged batter is proved to be withoutconductive part netted or any appearance deformation after discharge at 2CA for 5 minutes or 10CA for 5 seconds
11、严格遵照IEC 60896－2ir22，JISC 8704－2，GB／T19638 2等标准。
Design according with IEC 60896-21/22: 2004. JS C 8704-2, GB/T 19638.2, etc