小松挖掘机配件PC450-8液压泵散件，小松挖掘机液压泵总成

小松挖掘机配件PC450-8液压泵散件，小松挖掘机液压泵总成

联系人：陈元青 号:
电话：
邮箱：chenyuanqing2@
传真：
在线1097053265 号：
地址：济宁市高新区万丽富德广场22楼

708-2H-00027
泵总成.........................PUMP ASS'Y
此总成包括所有零件 FIGS.Y1600-01A0 T0
Y1600-11A0.
THIS ASSEMBLY CONSISTS OF ALL PARTS
SHOWN IN FIGS.Y1600-01A0 T0 Y1600-11A0.
708-2H-01027
• 泵分体总成................PUMP SUB ASS'Y
(a 708-2H-04670)
•• 壳体总成, 前 .........CASE ASS'Y, FRONT
A ••• 壳体, 前...................CASE, FRONT
A ••• 螺塞 ..............................PLUG
708-8E-16150
•• 螺塞...............................PLUG
07002-61023
•• O 形圈...........................O-RING
07000-B2012
•• O 形圈...........................O-RING
04530-11222
•• 螺栓, ........................BOLT, EYE
07044-12412
•• 螺塞...............................PLUG
07002-62434
•• O 形圈...........................O-RING
07040-12414
•• 螺塞...............................PLUG
07002-62434
•• O 形圈...........................O-RING
(708-2H-00027)
泵总成.........................PUMP ASS'Y
此总成包括所有零件 FIGS.Y1600-01A0 T0
Y1600-11A0.
THIS ASSEMBLY CONSISTS OF ALL PARTS
SHOWN IN FIGS.Y1600-01A0 T0 Y1600-11A0.
(708-2H-01027)
• 泵分体总成................PUMP SUB ASS'Y
(a 708-2H-04480)
•• 盖总成, 端部 ............CAP ASS'Y, END
A ••• 盖总成, 端部..................CAP, END
A ••• 螺塞 ..............................PLUG
(a 708-2H-12430)
•• 轴承............................BEARING
(a 07000-A5190)
•• O 形圈...........................O-RING
(a 04020-01434)
•• 定位销.......................PIN, DOWEL
(a 708-1L-29340)
•• 节流孔..........................ORIFICE
(a 01010-61860)
•• 螺栓...............................BOLT
(a 01643-31845)
•• 垫圈.............................WASHER
(a 708-2L-25480)
•• 过滤器...........................FILTER
708-8E-16150
•• 螺塞...............................PLUG
07002-61023
•• O 形圈...........................O-RING
07040-12414
•• 螺塞...............................PLUG
07002-62434
•• O 形圈...........................O-RING
(708-2H-00027)
泵总成.........................PUMP ASS'Y
此总成包括所有零件 FIGS.Y1600-01A0 T0
Y1600-11A0.
THIS ASSEMBLY CONSISTS OF ALL PARTS
SHOWN IN FIGS.Y1600-01A0 T0 Y1600-11A0.
(708-2H-01027)
• 泵分体总成................PUMP SUB ASS'Y
1 (a 708-2H-32110)
•• 轴................................SHAFT
2 (a 708-1H-22150)
•• 轴承............................BEARING
3 (a 708-17-05010)
•• 垫圈套件.....................WASHER KIT
A ••• 垫圈, 3.0MM..............WASHER, 3.0MM
A ••• 垫圈, 3.1MM..............WASHER, 3.1MM
A ••• 垫圈, 3.2MM..............WASHER, 3.2MM
4 (a 708-17-12780)
•• 环, 卡子 ....................RING, SNAP
5 708-27-22811
•• 密封, 油 .....................SEAL, OIL
6 708-2H-22160
•• 垫片.............................SPACER
7 04065-08225
•• 环, 卡子 ....................RING, SNAP
(a 708-2H-04750)
•• 气缸体总成.........CYLINDER BLOCK ASS'Y
8 A ••• 块, 油缸...............BLOCK, CYLINDER
9 A ••• 板, 气门杆................PLATE, VALVE
0 (a 708-18-13230)
•• 销..................................PIN
1 (a 04065-05820)
•• 环.................................RING
2 (a 708-2H-33140)
•• 座椅...............................SEAT
3 (a 708-2H-33150)
•• 弹簧.............................SPRING
4 (a 708-2H-23141)
•• 座椅...............................SEAT
5 (a 708-2H-23350)
•• 导管, 定位器 ...........GUIDE, RETAINER
6 (a 708-2H-23360)
•• 销..................................PIN
7 (a 708-2H-33343)
•• 定位器, 履带板 ..........RETAINER, SHOE
8 (a 708-2H-33311)
•• 柱塞分体总成...........PISTON SUB ASS'Y
(a 708-2H-04690)
•• 支承分体总成...........CRADLE SUB ASS'Y
9 A ••• 支承 ............................CRADLE
0 A ••• 凸轮, 摇臂.................CAM, ROCKER
1 (a 04020-01434)
•• 定位销.......................PIN, DOWEL
2 (a 07000-B1009)
•• O 形圈...........................O-RING
3 (a 01252-61235)
•• 螺栓...............................BOLT
SHOWN IN FIGS.Y1600-01A0 T0 Y1600-11A0.
(708-2H-01027)
• 泵分体总成................PUMP SUB ASS'Y
(a 708-2H-34150)
•• 滑块.............................SLIDER
(a 708-2H-03411)
•• 阀总成, PC .............VALVE ASS'Y, PC
(a 708-2H-03022)
••• 伺服活塞总成 .......PISTON ASS'Y, SERVO
A •••• 伺服活塞.................PISTON, SERVO
A •••• 螺钉.............................SCREW
(a 708-2G-15320)
••• 密封 ..............................SEAL
(a 708-2H-15310)
••• 螺塞 ..............................PLUG
(a 708-2L-35760)
••• 钢珠 ..............................BALL
(a 708-2L-35770)
••• 螺塞 ..............................PLUG
(a 708-2L-35690)
••• 密封 ..............................SEAL
(a 708-2L-35170)
••• 销 .................................PIN
(a 708-3M-15670)
••• 阀柱 .............................SPOOL
(a 708-2G-15290)
••• 定位器 ........................RETAINER
(a 708-2G-15140)
••• 座椅 ..............................SEAT
(a 708-2H-15330)
••• 弹簧 ............................SPRING
(a 708-2H-15320)
••• 弹簧 ............................SPRING
(a 708-2G-15151)
••• 座椅 ..............................SEAT
(a 708-2H-15340)
••• 弹簧 ............................SPRING
(a 708-2G-14340)
••• 螺钉 .............................SCREW
(a 07000-B3038)
••• O 形圈 ..........................O-RING
(a 708-2G-15230)
••• 环, 支承.................RING, BACK-UP
(a 708-2G-15260)
••• 密封 ..............................SEAL
(a 708-2G-15240)
••• 螺塞 ..............................PLUG
(a 07000-B2012)
••• O 形圈 ..........................O-RING
(a 07000-B2050)
••• O 形圈 ..........................O-RING
(a 708-2G-15310)
••• 环 ................................RING
(a 708-2L-44161)
••• 盖 ...............................COVER
(a 01580-10806)
••• 螺母 ...............................NUT
(a 708-2L-35540)
••• 螺母 ...............................NUT
(a 708-2G-15330)
••• 环, 电线....................RING, WIRE
(708-2H-01027)
• 泵分体总成................PUMP SUB ASS'Y
(a 708-2H-03510)
•• 盖组件......................COVER ASS'Y
(a 708-2G-14310)
••• 螺钉 .............................SCREW
(a 07000-B3038)
••• O 形圈 ..........................O-RING
(a 708-2G-15230)
••• 环, 支承.................RING, BACK-UP
(a 708-2L-35540)
••• 螺母 ...............................NUT
(a 708-2L-44130)
••• 盖 ...............................COVER
(a 07000-B2050)
••• O 形圈 ..........................O-RING
(a 708-2G-15310)
••• 环 ................................RING
(a 01252-61645)
•• 螺栓...............................BOLT
(708-2H-01027)
• 泵分体总成................PUMP SUB ASS'Y
(a 708-2H-04680)
•• 壳体总成, 后 ..........CASE ASS'Y, REAR
A ••• 壳体, 后....................CASE, REAR
A ••• 螺塞 ..............................PLUG
07044-12412
•• 螺塞...............................PLUG
07002-62434
•• O 形圈...........................O-RING
20B-27-11210
•• 排放器..........................BLEEDER
07000-B2012
•• O 形圈...........................O-RING
04530-11222
•• 螺栓, ........................BOLT, EYE
708-8E-16150
•• 螺塞...............................PLUG
07002-61023
•• O 形圈...........................O-RING
07040-12414
•• 螺塞...............................PLUG
07002-62434
•• O 形圈...........................O-RING
708-2H-01027)
• 泵分体总成................PUMP SUB ASS'Y
a 708-2H-32121)
•• 轴................................SHAFT
a 708-1H-22150)
•• 轴承............................BEARING
a 708-17-05010)
•• 垫圈套件.....................WASHER KIT
A ••• 垫圈, 3.0MM..............WASHER, 3.0MM
A ••• 垫圈, 3.1MM..............WASHER, 3.1MM
A ••• 垫圈, 3.2MM..............WASHER, 3.2MM
a 708-17-12780)
•• 环, 卡子 ....................RING, SNAP
a 708-2H-04760)
•• 块总成, 后 ...........BLOCK ASS'Y, REAR
A ••• 块, 油缸...............BLOCK, CYLINDER
A ••• 板, 气门杆................PLATE, VALVE
a 708-18-13230)
•• 销..................................PIN
a 04065-05820)
•• 环.................................RING
a 708-2H-33140)
•• 座椅...............................SEAT
a 708-2H-33150)
•• 弹簧.............................SPRING
a 708-2H-23141)
•• 座椅...............................SEAT
a 708-2H-23350)
•• 导管, 定位器 ...........GUIDE, RETAINER
a 708-2H-23360)
•• 销..................................PIN
a 708-2H-33343)
•• 定位器, 履带板 ..........RETAINER, SHOE
a 708-2H-33311)
•• 柱塞分体总成...........PISTON SUB ASS'Y
a 708-2H-04690)
•• 支承分体总成...........CRADLE SUB ASS'Y
A ••• 支承 ............................CRADLE
A ••• 凸轮, 摇臂.................CAM, ROCKER
a 04020-01434)
•• 定位销.......................PIN, DOWEL
a 07000-B1009)
•• O 形圈...........................O-RING
a 01252-61235)
•• 螺栓...............................BOLT
a 708-2H-32130)
•• 联轴器.........................COUPLING
a 708-2H-12420)
•• 环.................................RING
(708-2H-01027)
• 泵分体总成................PUMP SUB ASS'Y
(a 708-2H-34150)
•• 滑块.............................SLIDER
(a 708-2H-03411)
•• 阀总成, PC .............VALVE ASS'Y, PC
(a 708-2H-03022)
••• 伺服活塞总成 .......PISTON ASS'Y, SERVO
A •••• 伺服活塞.................PISTON, SERVO
A •••• 螺钉.............................SCREW
(a 708-2G-15320)
••• 密封 ..............................SEAL
(a 708-2H-15310)
••• 螺塞 ..............................PLUG
(a 708-2L-35760)
••• 钢珠 ..............................BALL
(a 708-2L-35770)
••• 螺塞 ..............................PLUG
(a 708-2L-35690)
••• 密封 ..............................SEAL
(a 708-2L-35170)
••• 销 .................................PIN
(a 708-3M-15670)
••• 阀柱 .............................SPOOL
(a 708-2G-15290)
••• 定位器 ........................RETAINER
(a 708-2G-15140)
••• 座椅 ..............................SEAT
(a 708-2H-15330)
••• 弹簧 ............................SPRING
(a 708-2H-15320)
••• 弹簧 ............................SPRING
(a 708-2G-15151)
••• 座椅 ..............................SEAT
(a 708-2H-15340)
••• 弹簧 ............................SPRING
(a 708-2G-14340)
••• 螺钉 .............................SCREW
(a 07000-B3038)
••• O 形圈 ..........................O-RING
(a 708-2G-15230)
••• 环, 支承.................RING, BACK-UP
(a 708-2G-15260)
••• 密封 ..............................SEAL
(a 708-2G-15240)
••• 螺塞 ..............................PLUG
(a 07000-B2012)
••• O 形圈 ..........................O-RING
(a 07000-B2050)
••• O 形圈 ..........................O-RING
(a 708-2G-15310)
••• 环 ................................RING
(a 708-2L-44161)
••• 盖 ...............................COVER
(a 01580-10806)
••• 螺母 ...............................NUT
(a 708-2L-35540)
••• 螺母 ...............................NUT
(a 708-2G-15330)
••• 环, 电线....................RING, WIRE
708-2H-03610
• 阀总成, LS..............VALVE ASS'Y, LS
(a 708-2L-35311)
•• 套筒.............................SLEEVE
708-2L-24680
•• 密封...............................SEAL
(a 708-2G-15412)
•• 阀柱..............................SPOOL
(a 708-2L-28540)
•• 活塞.............................PISTON
(a 708-2L-35360)
•• 套筒.............................SLEEVE
(a 708-2L-35331)
•• 座椅...............................SEAT
(a 708-2L-35410)
•• 弹簧.............................SPRING
(a 708-2L-35341)
•• 座椅...............................SEAT
(a 708-2L-35351)
•• 螺塞...............................PLUG
(a 07000-B1009)
•• O 形圈...........................O-RING
(a 07001-01009)
•• 环, 支承 .................RING, BACK-UP
01583-11408
•• 螺母................................NUT
07002-62434
•• O 形圈...........................O-RING