ISED下发IC认证SAR报告相关注意事项通知

ISED近期通知所有的FCB留意以下SAR报告相关事项，实验室需留意，以避免IC认证时报告被卡。

　　测试报告不完整或不正确：

　　１、如RSS-102 Annex E中所要求的，测试报告应该包含测试中所使用的head或body的模型描述，包括模型的 厚度和其它公差。
　　２、如RSS-102 2.2章节所提及的，要把设备校验作为RF exposure Technical Brief的一部分。SAR测试使用的所有仪器，含系统确认和电介质的验证，均在仪器清单中列明仪器以证明符合RSS-102。此部分包含但不限于在系统确认中使用的信号发生器，方向耦合器，功率量测仪，功率传感器，滤波器，衰减器，和用于验证组织液的电介质探针工具箱。
　　３、在SAR测试之前确保SAR测试系统使用新校验的e-field探针转换因子进行设置，不接受使用不同的转换因子进行系统确认，系统验证和SAR合规评估。
　　４、如RSS-102 Issue 5第3章节所提及的，依据IEEE 1528/IEC 62209的新版本做SAR评估。目前IEEE 1528-2013和IEC 62209-2(2010)包括的技术规格测试机制有限，当前可以使用RSS-102所列的FCC KDB，直到国际标准涵盖相应的程序。当要求测试head SAR或body SAR时，依据IEEE 1528-2013和IEC 62209-2(2010)执行不确定度预算分析。并且，包含（但不限于）探针调整反应不确定度和组织液温度不确定度。

以下为ISED的通知原文供参考：
************************************************************************************
　　To whom it may concern,

　　Innovation, Science and Economic Development Canada wishes to remind the following:

Incomplete / incorrect test report
　　１、As referenced in Annex E of RSS-102 the test report shall include the description of the head and/or body phantoms used in the tests, including shell thickness and other tolerances.

　　２、As referenced in section 2.2 of RSS-102, "equipment calibrations" is required as part of the RF Exposure Technical Brief. All equipment used in the SAR evaluations, including System Check and dielectric verification must be provided in the equipment list to demonstrate compliance to RSS-102. This would include, but not limited to signal generators, directional couplers, power meters and power sensors, filters and attenuators used during System Check, and the dielectric probe kit used to verify tissue simulating liquid.

　　３、It must be ensured that the SAR measurement system is configured to use the most recent calibrated e-field probe conversion factors before SAR measurements are performed. It is not acceptable to use different conversion factors for the system check, system validation and SAR compliance evaluations.

　　４、As stated in section 3 of RSS-102, Issue 5, “SAR evaluations shall be made in accordance with the latest version of IEEE 1528 and/or IEC 62209.” Presently, IEEE1528-2013 and IEC62209-2 (2010) are the most recent versions of the standards. As such, these standards must be used for head and body SAR evaluations respectively including the uncertainty analysis. Since IEEE1528-2013 and IEC62209-2 (2010) contain limited technology specific testing protocols, FCC KDB publications listed in RSS-102 can be used in the interim until such procedures are included in the international standards. When head and/or body SAR measurements are required, the uncertainty budget analysis must be conducted as per IEEE1528-2013 and IEC62209-2 (2010) and shall include (but are not limited to) probe modulation response uncertainty and liquid temperature uncertainty.
***************************************************************************************